[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]
Re: [TCML] Testing a tripler
Well, I still haven't been able to figure out if the triplers are in good
order or not. I wasn't able to implement Carl's suggestions below due to a
lack of an adequate power supply.
The tripler has four inputs and one HV output. The inputs are:
U~ is the connection for AC in
UF is for focus control
A is neutral or ground
D I don't know what D is for.
So I set my little pocket meter to measure resistance:
the first tripler:
U~ and A gets a reading of 1.55 megaohms
U~ and UF 175 Ohms
U~ and D OL
A and D OL
A and UF 1.64 megaohms
A or U~ and the HV output is OL
the second tripler:
U~ and A 300.8 kOhms
U~ and UF 5.71 kOhms
U~ and D OL
A and D OL
A and UF 295.6 kOhms
How do these sound?
I'm trying to build a HV DC power supply using an ignition coil, dimmer, cap
and tripler. Everything works fine until I add the tripler, then I seem to
get no measurable output. I guess they're toast, but I'd appreciate any
advice before I give up.
Paul
----- Original Message -----
From: "Carl Noggle" <cn@xxxxx>
To: "Tesla Coil Mailing List" <tesla@xxxxxxxxxx>
Sent: Friday, February 17, 2012 12:59 PM
Subject: Re: [TCML] Testing a tripler
There's a schematic at this URL--
http://www.google.com/imgres?q=voltage+tripler&num=10&um=1&hl=en&safe=off&client=firefox-a&rls=org.mozilla:en-US:official&biw=1680&bih=909&tbm=isch&tbnid=50PB-rvzowc_TM:&imgrefurl=http://www.play-hookey.com/ac_theory/ps_v_multipliers.html&docid=QyQbSsppcH_jeM&imgurl=http://www.play-hookey.com/ac_theory/images/rectifier_tripler.gif&w=250&h=125&ei=-ZI-T4qEAYqyiQLasLmIAQ&zoom=1&iact=hc&vpx=394&vpy=346&dur=608&hovh=98&hovw=197&tx=95&ty=44&sig=113737727595651070905&sqi=2&page=1&tbnh=81&tbnw=162&start=0&ndsp=40&ved=0CGgQrQMwCQ
( I think that's the longest one I've ever seen.)
Each of the diodes has about 20 junctions or so in series, so the forward
voltage drop is of the order of 13 volts. The drop from U to A will be
about 40 volts. If you have a power supply at voltages like this and can
limit the current to about one mA or less, you can test it like a
diode--should be a drop of tens of volts one way and open the other way.
If the drop is the same in both directions the tripler is hosed.
The D must be where the flyback xfmr feeds in. The diodes in these units
can only handle about 3mA or so average current. To get good operation,
the input will have to be about 5kHz or more.
---Carl
I was hoping for a little advice. I obtained a couple of TV voltage
triplers (part number 1895-641-095). These are voltage multipliers used
mainly in older TVs to boost and rectify voltage to the picture tube.
They seem OK, but I'd like to test them before going to all the trouble
of assembling components around them to produce HV DC. I can't seem to
find specs or meter readings for them. Anyone know what values I should
get testing them with a multimeter?
There are four inputs: D, A, U~ and UF. UF is for focus control. U~ is
the hot lead, A is neutral or ground. I'm not sure what D is for.
There's one HV output. It has a suction cup connector on it, like you see
on flybacks.
Any tips?
PBT
_______________________________________________
Tesla mailing list
Tesla@xxxxxxxxxx
http://www.pupman.com/mailman/listinfo/tesla
_______________________________________________
Tesla mailing list
Tesla@xxxxxxxxxx
http://www.pupman.com/mailman/listinfo/tesla
_______________________________________________
Tesla mailing list
Tesla@xxxxxxxxxx
http://www.pupman.com/mailman/listinfo/tesla