[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]
Re: Apology -- was:Re: [TCML] Q,,question
Yep. I previously bought a flyback and a 8.5" x 34"
OWL toroid from you. I was very impressed how you
worked with me, since I was out of the country when
the BIG toroid bulk buy went down several years ago.
Adam
--- resonance <resonance@xxxxxxxxxxxx> wrote:
>
>
> No offense was taken. I didn't quite understand
> your meaning in the
> original post.
>
> BTW, were you the person looking for some caps ---
> perhaps the large Maxwell
> 0.1 uF 60 kV cap I have?
>
> Dr. Resonance
>
> Resonance Research Corp.
> www.resonanceresearch.com
>
>
> ----- Original Message -----
> From: "Yurtle Turtle" <yurtle_t@xxxxxxxxx>
> To: "Tesla Coil Mailing List" <tesla@xxxxxxxxxx>
> Sent: Saturday, December 08, 2007 3:08 PM
> Subject: Re: Apology -- was:Re: [TCML] Q,,question
>
>
> >I think you and I are being overly sensitive here.
> I
> > didn't take your statement any way other than you
> > intended. I did mean it in a somewhat sarcastic
> > manner, though I also believe it to be a realistic
> -
> > though difficult - way to handle corona on thin
> > ribbon. I suspect most of us list members have
> fairly
> > thick skins, though we keep having new folks show
> up,
> > who may not have my sense of humor. I just wanted
> to
> > point out that while I consider my suggestion
> > ridiculous, I didn't mean it to be insulting. It
> would
> > be ridiculous for me to try to wind a pig, but
> Finn's
> > is truely a work of art. We all remember over
> eager
> > newbies who shoot for the impossible. It's
> probably OK
> > to tell them if the view doesn't warrant the
> climb.
> > However, we also have read about folks who have
> done
> > the impossible, so I try not to discourage the
> > impossible. Conventional wisdom says NEVER try to
> > drill holes and thread 50 feet of 1/4" tubing
> through
> > eight primary supports, but I ignored that and got
> a
> > decent looking primary:
> >
> > http://www.hot-streamer.com/adam/primary.htm
> >
> > Adam
> >
> > --- David Rieben <drieben@xxxxxxxxxxx> wrote:
> >
> >> Hi Adam, and all,
> >>
> >> After reviewing my own words, I believe that I
> >> personally owe Adam
> >> an apology. The statement "being humorously
> >> sarcastic" was a poor
> >> choice of words on my part as it was certainly
> not
> >> my intent to
> >> imply that Adam was trying to be rude or
> insulting,
> >> only that he
> >> was joking. A check of the dictionary reveals
> that
> >> in most circum-
> >> stances, the term "sarcasm" has a definite
> negative
> >> conotation. Open
> >> mouth, insert foot, David ;^( I have met Adam and
> >> consider him a
> >> very good personal friend and would certainly
> never
> >> intentionally try
> >> to paraphrase his statements in a malicious way.
> >> Again Adam, please
> >> accept my apology for putting you in the
> >> uncomfortable situation of
> >> having to explain the intent of your statement as
> >> that was certainly
> >> not my intention.
> >>
> >> Sincerely,
> >> David
> >>
> >>
> >> ----- Original Message -----
> >> From: "Yurtle Turtle" <yurtle_t@xxxxxxxxx>
> >> To: "Tesla Coil Mailing List" <tesla@xxxxxxxxxx>
> >> Sent: Saturday, December 08, 2007 10:43 AM
> >> Subject: Re: [TCML] Q,,question
> >>
> >>
> >> > While I was joking, I never meant it as an
> insult.
> >> In
> >> > fact, I WAS half-way serious about a possible
> way
> >> to
> >> > handle the edge corona. While it may seem like
> too
> >> > much trouble for most of us, consider the
> >> following:
> >> > How many people would seriously consider
> >> fabricating
> >> > their own spun-aluminum toroids, winding their
> own
> >> > "variacs", or even winding their own pigs? Yet
> >> some of
> >> > our very own list members have not only done
> the
> >> > above, but have done so elegantly.
> >> >
> >> > Adam
> >> >
> >> > --- johnbrooks@xxxxxxxxxxx wrote:
> >> >
> >> >> Could be he was. It was an idea that I thought
> >> was
> >> >> feasible.
> >> >> I have several hundred lbs litz #3
> stranded(Iknow
> >> >> ,,can't be tapped)
> >> >> Perhaps I will go with the 80% Litz,,20%
> strap.
> >> I'm
> >> >> looking for least
> >> >> primary turns possible for a 16"D wound w/#14
> >> magnet
> >> >> for 80 inches
> >> >> secondary.
> >> >>
> >> >> Thanks for all the feedback.
> >> >> j
> >> >>
> >> >>
> >> >>
> >> >> On Thu, 6 Dec 2007 23:39:59 -0600, "David
> Rieben"
> >> >> <drieben@xxxxxxxxxxx>
> >> >> said:
> >> >> > Hi Dr. Res,
> >> >> >
> >> >> > I think Adam was being humorously
> sarcastic....
> >> >> >
> >> >> > David
> >>
> >>
> >> _______________________________________________
> >> Tesla mailing list
> >> Tesla@xxxxxxxxxxxxxx
> >> http://www.pupman.com/mailman/listinfo/tesla
> >>
> >
> >
> >
> >
> >
>
____________________________________________________________________________________
> > Never miss a thing. Make Yahoo your home page.
> > http://www.yahoo.com/r/hs
> > _______________________________________________
> > Tesla mailing list
> > Tesla@xxxxxxxxxxxxxx
> > http://www.pupman.com/mailman/listinfo/tesla
> >
>
>
> _______________________________________________
> Tesla mailing list
> Tesla@xxxxxxxxxxxxxx
> http://www.pupman.com/mailman/listinfo/tesla
>
____________________________________________________________________________________
Looking for last minute shopping deals?
Find them fast with Yahoo! Search. http://tools.search.yahoo.com/newsearch/category.php?category=shopping
_______________________________________________
Tesla mailing list
Tesla@xxxxxxxxxxxxxx
http://www.pupman.com/mailman/listinfo/tesla