[Home][2014 Index] Re: [TCML] 10 foot tall Tesla Coil [Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

Re: [TCML] 10 foot tall Tesla Coil



Jeff,
I'm glad to hear you didn't go for a smaller toroid - as was your own
choice, ideally something even bigger than the 48 inch would not have been
lost. A big benefit being it would protect your primary more. (it solved my
own primary strikes) The 12 inch minor sounds just the right size. 
Spurred on by the 'Green Monster' proportions, I was recently lucky enough
to borrow a 50 x 11 inch toroid for my own 8 inch coil, replacing its normal
34 x 8 inch, and I saw quite a marked difference in performance, (it was
fairly well optimised anyway, and tuning was allowed for).  
At 15.6 pounds hand made from Aluminium sheeting it is also considerably
lighter as well, so lightweight designs can be achieved.
Yours should have a nice raspy sound to it with that static gap as well, as
the drone of an SRSG can get tiresome after a while.
Let us all know when a video is available.

Phil

-----Original Message-----
From: tesla-bounces@xxxxxxxxxx [mailto:tesla-bounces@xxxxxxxxxx] On Behalf
Of Jeff Behary
Sent: 17 May 2014 02:27
To: tesla@xxxxxxxxxx
Subject: [TCML] 10 foot tall Tesla Coil

I've been distant a year or more, chaos in life as I'm sure everyone has
lately.
But some may recall a large coil I started on my birthday last year.  Its
made for a major
future Tesla museum (not Wardenclyffe) that I must refrain speaking about
too much for the moment.
It's personally dedicated to Bill Wysock, Harry Goldman, Kenneth
Strickfaden, and the long list of other
friends and pioneers in the field.  Not meant to be the biggest or best coil
on earth but something
different...and yet the same.  Powered  by a 10KVA pole pig, 120/240 -
14.4kV single phase.
.1 mfd 100kV cap bank.  2" flat ribbon and EPDM rubber primary coil.  10.75"
x 75" secondary coil
threaded 14 turns per inch and inlaid with 16 AWG wire.  48" diameter x 12"
cross section toroid.
The spark gap is a 12-series 1/2" tungsten oil-cooled gap, made to handle
high currents.  I specifically 
wanted something different here, as I know Bill and Harry would be amused to
see such a drastic departure...
(but its not so far off from early high power transmitter designs...just a
little engine like :) ! )

First light didn't happen when it should've (last weekend).  Meant to run
from 240V 50A...but I only have access to a 240V 30A line 
out in the country where I can safely test it...and my ballasts were
consuming all of the current instead of limiting it...by poor pig 
was only putting out about 15mA, LOL, and I was still blowing the 30A fuse,
talk about a kick in the butt after a long day of work...
by the time I started tinkering with the power supply and figured out the
problem it was late at night.  Had spent 12 hours in the sun 
drilling 2" thick GPO, fun but not fun if you know what I mean... and it
took us 2 hours to figure out how to get a 4 foot
toroid 11 feet in the air for lowering it...don't laugh...its easier said
than done!  They're like picking up a greased aluminum pig.
The good news my pole pig afterward threw white hot arcs instead of 1/2"
blue sparks :/ !!! and still even at seriously no power to
speak of I was getting 4' sparks.  Hoping for at least 9-10 ft on 30A and
15-16 on 50A.  Of course more would be better but this
gap being stationary and higher powered (and low BPS) should make some nice
slow hot arcs.  Rain all week here, but weekend forecast
is clear...so wish us luck tomorrow :) !

I am really happy with the PVC tie rod made from 3" PVC pipe.  The secondary
coil keys in to holes on the base top and is screwed down from
below using 1/2" bolts.  At the top of the coil of course there is no metal.
But the secondary coil weighs 75 pounds, is tall, and the 100 pound
oversized toroid doesn't help matters.  I didn't want any chances of it all
falling over in the wind...

The coil is horrifically heavy... in fact a 1/2 ton.  When finished it must
be OSHA compliant, no seriously, stop laughing.  I can't
give away too much, but it really will be.  What I can assure everyone, is
that the final installation site will be a place you all want
to go.  Regardless of the big coil... it will be Tesla paradise ;) ...

http://www.electrotherapymuseum.com/2014/BigCoil/index.html


Its not to typical specs, I didn't want such a large topload but the man
paying the bill did and I didn't argue as there were two for sale.
Terry I can't blame you for wanting to get rid of them.  I had to rent a
Hope Depot truck just to transport them to the test site, only to 
have my parents run their car battery flat.  It took 3 hours and $100 to
move them 20 miles...!!!
Endless thanks to everyone who has "friended" me on Facebook, its so nice to
see faces with names and how similar we all are at the end
of the day...

Jeff
 		 	   		  
_______________________________________________
Tesla mailing list
Tesla@xxxxxxxxxx
http://www.pupman.com/mailman/listinfo/tesla

_______________________________________________
Tesla mailing list
Tesla@xxxxxxxxxx
http://www.pupman.com/mailman/listinfo/tesla