[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]
RE: [TCML] Lacquer
Hi
Is that foil thing on the floor a capacitor or what? If so, how is it
constructed?
Kiwi Newbie
-----Original Message-----
From: Phillip Slawinski [mailto:pslawinski@xxxxxxxxx]
Sent: Friday, 9 April 2010 2:17 a.m.
To: Tesla Coil Mailing List
Subject: Re: [TCML] Lacquer
Hi All,
I too use the two-part epoxy coating on all my coils. I built a coil from
the ground up to produce a long spark length compared to the secondary
length. It has taken a lot of work, but I think the results were worth it.
http://www.flickr.com/photos/pslawinski/4354745760/ During the process of
developing this coil I have had multiple flash overs.
http://www.flickr.com/photos/pslawinski/4309814799/ I haven't lost a
secondary to a flash over or spark related event. My secondary is wound
with 34 AWG on a 12" x 3.5" form. Not coating a form with such fine wire is
simply not an option. The wire is very fragile, and will break with only a
mild amount of force, also with wire this fine expansion and contraction of
the form due to temperature change will cause the windings to loosen up and
fall down. Sadly, I know this from experience.
-Phillip Slawinski
On Thu, Apr 8, 2010 at 08:22, Peter Terren <pterren@xxxxxxxxxxxx> wrote:
> Firstly, the experiment with the conventional coil is not conclusive,
> sorry. Power was "about 20%" in the pre shot with racing sparks. No
> mention of actual values for the post shot and the sparks look very
> different on the pics.
> I am not saying the result is wrong, but it is highly likely the
> original power level was not reproduced.
>
> Secondly, DRSSTC's are different beasts in terms of coupling.
> Obtaining better Watt's ratios (spark length/sec length) seems a lot
> easier. 13:4 =
> 3.25 does not seem remarkably efficient in this regard.
> On the other hand using an SGTC coil with no special insulation, I
> have Watt's ratios of 3.0 (96inches/32in). Others have claimed larger
> ratios for SGTC's but I have not seen clear photos to show this. If
> you want to follow this link copy and paste it into your browser.
> http://tesladownunder.com/tesla_coil_sparks.htm#6 inch coil (the best
> ones)
>
> Nevertheless, the previous discussion of using ?Envirotex as a very
> thick layer does really seem to provide a lot of protection.
> Some years ago I started a TC project to dramatically outperform this
> 3.0 Watts number. A lot of special fabrication was done and I still
> have everything ready to start some final plans and construction. One
> day when I have a few moments........
>
> Peter
>
>
>
>
> On 8/04/2010 1:16 PM, Dr.Hankenstein wrote:
>
>> Greetings,
>>
>> If you're not too sure on the effects of a good coating (or two or
>> three) of varnish; please refer to a scientific evaluation on the
>> following link:
>>
>> http://www.audiotesla.org/corona%20experiment.htm
>>
>> This should remove all doubt that varnish does more than just hold
>> the winding in place and end the hypothetical armchair speculation. Dr.
>> Spark has at least 80 coats of varnish on "Fatboy"---13+ footers out
>> of a 4 foot secondary proves it:
>> http://www.drspark.org/fatboy1_rebuild.htm
>>
>> Regards,
>> Hank
>>
>> _______________________________________________
> Tesla mailing list
> Tesla@xxxxxxxxxx
> http://www.pupman.com/mailman/listinfo/tesla
>
__________ Information from ESET NOD32 Antivirus, version of virus signature
database 5012 (20100409) __________
The message was checked by ESET NOD32 Antivirus.
http://www.eset.com
__________ Information from ESET NOD32 Antivirus, version of virus signature
database 5012 (20100409) __________
The message was checked by ESET NOD32 Antivirus.
http://www.eset.com
_______________________________________________
Tesla mailing list
Tesla@xxxxxxxxxx
http://www.pupman.com/mailman/listinfo/tesla