Here is the output from JAVATC, the only thing that might not be
quite right is the spark gap. I might well remake it soon though to
get the gap smaller.
Thanks again for your help
Simon
Secondary Coil Inputs:
5.5 = Radius 1
5.5 = Radius 2
45 = Height 1
110 = Height 2
1300 = Turns
0.05 = Wire Diameter
---------------------------------------------------- Primary Coil
Inputs: ----------------------------------------------------
15 = Radius 1
50 = Radius 2
1 = Height 1
1 = Height 2
11 = Turns
1 = Wire Diameter
0.02 = Primary Cap (uF)
20 = Total Lead Length
1 = Lead Diameter
---------------------------------------------------- Top Load
Inputs: ----------------------------------------------------
Toroid #1: minor=13, major=41, height=120, topload
-------- Transformer Inputs:
----------------------------------------------------
240 [volts] = Transformer Rated Input Voltage
8500 [volts] = Transformer Rated Output Voltage
50 [mA] = Transformer Rated Output Current
50 [Hz] = Mains Frequency
240 [volts] = Transformer Applied Voltage
0 [amps] = Transformer Ballast Current
0 [ohms] = Measured Primary Resistance
0 [ohms] = Measured Secondary Resistance
---------------------------------------------------- Static Spark
Gap Outputs: ----------------------------------------------------
0.031 [cm] = Gap Spacing Between Each Electrode
12021 [peak volts] = Charging Voltage
8388 [peak volts] = Arc Voltage
39436 [volts] = Voltage Gradient at Electrode
33552 [volts/cm] = Arc Voltage per unit
69.8 [%] = Percent Cp Charged When Gap Fires
4.826 [ms] = Time To Arc Voltage
207 [BPS] = Breaks Per Second
0.7 [joules] = Effective Cap Energy
263476 [peak volts] = Terminal Voltage
146 [power] = Energy Across Gap
78.2 [cm] = Static Gap Spark Length (using energy equation)
On 7 Aug 2009, at 01:30, bartb wrote:
Simon,
If you do as Phil suggested, delete out all the unnecessary stuff
to keep the data compact (really, just inputs are needed).
Bart
Phil Tuck (hvtesla) wrote:
Simon.
If you used JAVATC the best option would be to run JAVATC and
then use the
'Format Design as text' button. Then cut and paste the results
into your
email. That way the more learned members (I'm most certainly not
one) can
advise you better.
Phil
-----Original Message-----
From: tesla-bounces@xxxxxxxxxx [mailto:tesla-bounces@xxxxxxxxxx]
On Behalf
Of Simon Dodd
Sent: 06 August 2009 03:26
To: Tesla Coil Mailing List
Subject: Re: [TCML] breakouts and a picture
OK, here goes, In the video I didn't do any tuning but the
second firing was at a festival and I did a bit of tuning which
improved the spark length but still no breakouts. I am using a
4" PVC tube with copper tube inside, the same as a lot of
designs I have seen. I used JAVATC to get my dimensions and my
capacitor is an MMC type.
I noticed when I was tuning and getting small improvements The
shock to my arm was increasing more than expected so I stopped
using a non grounded rod very quickly!!
The picture is now at www.djodd.co.uk/tesla
Thanks
Simon
On 6 Aug 2009, at 00:40, Lau, Gary wrote:
Hi Simon,
The TCML does not permit attachments, so we didn't see the
picture.
The first question that must be answered in troubleshooting a
coil is, is the primary in tune with the secondary? In your
video, I didn't hear any mention of tuning. Have you tried
tapping the primary differently and determined if it improves
or degrades performance? Did you use some type of design
software to choose the components?
And there's any number of other issues that we can't deduce
from your video. Details of the spark gap, and capacitor type.
When you do get your coil running well, you probably shouldn't
try holding the metal rod in your hand and drawing sparks to
it, unless the rod is securely wired to a good ground. You
don't want that current flowing through your body!
Regards, Gary Lau
MA, USA
-----Original Message-----
From: tesla-bounces@xxxxxxxxxx [mailto:tesla-
bounces@xxxxxxxxxx] On
Behalf Of Simon Dodd
Sent: Wednesday, August 05, 2009 5:04 AM
To: Tesla Coil Mailing List
Subject: [TCML] breakouts and a picture
Hi Guys,
Here is a picture of the second firing of my coil, I was getting
streamers to a grounded point about 10-15cm away. However I
would
like to get streamers leaving the torroid to the air rather
than a
grounded point. Is this just a question of tuning or would a
change in
torroid make a difference?
The coil is a SGTC with an 8.5Kv 50mA NST. The secondary is about
23" (I have the exact measurement written down somewhere!)
You get an idea of the design from this photo and I also posted
the
video of the first firing a while ago but here is the link
again, it
has more closeups of the coil.
http://www.youtube.com/watch?v=kdQ6IsJtUU0
Let me know if you need more information to help me.
Thanks in advance
Simon
_______________________________________________
Tesla mailing list
Tesla@xxxxxxxxxxxxxx
http://www.pupman.com/mailman/listinfo/tesla
_______________________________________________
Tesla mailing list
Tesla@xxxxxxxxxxxxxx
http://www.pupman.com/mailman/listinfo/tesla
No virus found in this incoming message.
Checked by AVG - www.avg.com Version: 8.5.392 / Virus Database:
270.13.45/2284 - Release Date: 08/05/09
18:23:00
_______________________________________________
Tesla mailing list
Tesla@xxxxxxxxxxxxxx
http://www.pupman.com/mailman/listinfo/tesla
_______________________________________________
Tesla mailing list
Tesla@xxxxxxxxxxxxxx
http://www.pupman.com/mailman/listinfo/tesla
_______________________________________________
Tesla mailing list
Tesla@xxxxxxxxxxxxxx
http://www.pupman.com/mailman/listinfo/tesla