Re: For Sale: Complete 4" coil ; 5"x16" toroid on top of 6" toroid ; conical primary ; 60A 15KV transformer and 2.5KVA variac (fwd)

["Tesla list" <tesla@xxxxxxxxxx>]

---------- Forwarded message ----------
Date: Sat, 1 Sep 2007 13:58:12 -0600
From: Gomez Addams <gomezaddams@xxxxxxxxx>
To: Tesla list <tesla@xxxxxxxxxx>
Subject: Re: For Sale:  Complete 4" coil ; 5"x16" toroid on top of 6" toroid ;
    conical primary ; 60A 15KV transformer and 2.5KVA variac (fwd)

60A @ 15kV is 900,000 watts.
Did you mean 60mA?
Correct abbreviations matter.

On Sep 1, 2007, at 1:18 PM, Tesla list wrote:

>
> ---------- Forwarded message ----------
> Date: Fri, 31 Aug 2007 17:09:43 -0500
> From: "westland@xxxxxx" <westland@xxxxxx>
> To: Tesla list <tesla@xxxxxxxxxx>
> Subject: For Sale:  Complete 4" coil ; 5"x16" toroid on top of 6"  
> toroid ;
>     conical primary ; 60A 15KV transformer and 2.5KVA variac
>
> /*For Sale:  Complete Working Tesla Coil.  I would prefer to sell to
> experienced coilers*/
>
>    1. 4 inch x  22 inch (approx.) Tesla Coil Secondary. It is wound  
> on a
>       4 inch PVC form (4.2 Inch OD) and is about 1000 turns of heavy,
>       high temp #24 awg wire (HAPT). It's coated with two coats of
>       styrofoam. It's approx 24 inches tall with the included  
> insulator
>       top load mount. Included are also both end caps. One custom
>       external cap for the top and a sturdy 1/4 inch x 1 3/4  internal
>       one for the bottom. Also included are (3) 1/4-20 nylon bolts to
>       mount the base, one for the center mounting hole and two more  
> for
>       the holes you drill through the side wall when you have it in
>       final position. Resonate frequency is approx 285 kHz from  
> Tesla Stuff
>    2. Control box with John Frau phase shift variac (for synchronous
>       rotary gap below),  volt and ammeters, fuses and emergency  
> cut switch
>    3. 5"x16" toroid on top of 6" toroid  (both from John Frau) ...  
> looks
>       sharp
>    4. Conical primary 14 turns of 1/4" copper tubing;
>    5. 60A 15KV transformer (2x30a at 50Hz) 220VAC  input
>    6. 2.5KVA variac; 110 or 220 VAC input; 0 - 240 output
>    7. 15 x CDE 942 Capacitors on Perspex base with flexable tuning
>       arrangement
>    8. 10 Meg 1/2 watt Ohm Bleed Resistors + one large 20MV bleed  
> for the
>       entire array
>    9. Terry Filter with brass discharge balls  :-)  and perspex base
>       (From Tesla Stuff)
>   10. 2 x Richard Quick Gaps
>   11. 1 x synchronous motor rotary gap with 1/4" Tungsten rods and
>       Tungsten locking collars from Tesla Stuff; on perspex base
>   12. Good looking wooden box (Ikea) which holds Terry Filter, Caps  
> and
>       Rotary Gap (all on Perspex bases) very neatly
>
> /*So far around 40" sparks ... email me for pictures
>
> Price $1500
>
> Please email me at westland@xxxxxxx
> */
>
>
>

......................................................................
"To avoid damage to your system, only your SGI system support engineer
(SSE) can set the power switch to On or Off." - SGI Origin 3000 docs