RE: Schematic...

["Tesla list" <tesla@xxxxxxxxxx>]

Original poster: Yurtle Turtle <yurtle_t@xxxxxxxxx>

Feel free. I use Visio to draw it, then "print" it to
Adobe Acrobat Pro.

Transient Voltage Surge Supressor, and yes, I'm
probably overvolting it. I need to run it up on a JL
and monitor the current, just to see what's happening.
I may end up removing it, but since I had one for
free, I thought I'd use it.

Adam

--- Tesla list <tesla@xxxxxxxxxx> wrote:

> Original poster: "Jim Mora" <jmora@xxxxxxxxxxx>
>
> Hi Adam,
>
> Nice schematic! You don't mind if I hitch an idea or
> two off it do you? I
> have a 60amp filter IN my disconnect box at my
> control point, as from what I
> read, RF has a way of getting around things and
> exploiting wire paths. The
> box further shields it. I have two more I can use
> downstream! My computers
> so far run fine in the house...(all dedicated lines.
> My rack is on a APC
> 3000, 30amp 120v service). We saw what happens when
> you mess with an APC
> from the Geek group. At one time I used to see some
> posts from a user that
> had a domain address at APC, are you still on the
> list?
>
> Question: what is a TVSS and aren't you over volting
> it a small bit as it is
> for wye connection?
>
> Thanks,
> Jim Mora
>
>
>
> -----Original Message-----
> From: Tesla list [mailto:tesla@xxxxxxxxxx]
> Sent: Wednesday, November 22, 2006 9:19 AM
> To: tesla@xxxxxxxxxx
> Subject: Re: Schematic...
>
> Original poster: Yurtle Turtle <yurtle_t@xxxxxxxxx>
>
> Your Buzz box looks diferent than mine. I don't get
> the variable resistors, but it looks like "B" is
> closer to what I'd use. My current schematic can be
> seen at:
>
http://www.hot-streamer.com/adam/bigass_coil/schematic.pdf
>
> Which is far more complicated than you were looking
> for.
>
> When I used my welder, it looked like this:
>
>
http://www.hot-streamer.com/adam/garage/schematic_old.pdf
>
> Adam
>
> --- Tesla list <tesla@xxxxxxxxxx> wrote:
>
>   > Original poster: "Chip Ford"
> <chipford@xxxxxxxxxxxx>
>   >
>   > OK. First, let me say this. I know I am ignorant
> of
>   > alot of thing
>   > when it comes to electronics and building a
> tesla
>   > coil. That is why I
>   > am here and asking so many questions. To learn.
>   > Noone here on this
>   > board was born with any of this knowledge. We
> all
>   > have to learn what
>   > we want to know at some point. So please be
> patient
>   > and kind to me. I
>   > am trying to learn something here. There is a
> wealth
>   > of knowledge and
>   > experience here that money can't buy. Not that I
>   > could afford it if
>   > you could...OK..enough of that...
>   >
>   > I have attached a pic of (2) schematics
> representing
>   > (2) approaches
>   > to a TC curcuit with a ballast in it. By the
> way. I
>   > draw in Autocad
>   > for a living. Please let me know which one.
> Drawing
>   > "A", or Drawing
>   > "B", best represents the proper intruduction of
> a
>   > ballast into the
>   > curcuit. Or if neither is a good example. Also
> let
>   > me know if you see
>   > any other mistakes. Thank you...Chip
>   >
>   > http://hot-streamer.com/temp/Schematic1--7.JPG
>   >
>   >
>   >
>   >
>
>
>