[Prev][Next][Index][Thread]

Re: RE>Re: Testing capacitors ( (fwd)



---------- Forwarded message ----------
Date: Tue, 28 Jul 1998 23:57:27 -0600
From: "D.C. Cox" <DR.RESONANCE-at-next-wave-dot-net>
To: Tesla List <tesla-at-pupman-dot-com>
Subject: Re: RE>Re: Testing capacitors ( (fwd)

to: Dale

For the record, most of GE's X-Ray caps are manufactured by Plastic
Capacitors, Inc., in Chicago, IL.   We carry them in stock and derate them
for Tesla coil service to 50 kV.  Value is .01 MFD with 1/4 inch stud
terminals -- lower one exits side of case and upper terminal exits directly
on top of brown phenolic case.  They work great with NST coils and also
synchro RSG's.

DR.RESONANCE-at-next-wave-dot-net


----------
> From: Tesla List <tesla-at-pupman-dot-com>
> To: tesla-at-pupman-dot-com
> Subject: RE>Re: Testing capacitors ( (fwd)
> Date: Tuesday, July 28, 1998 9:03 PM
> 
> 
> 
> ---------- Forwarded message ----------
> Date: 28 Jul 1998 12:53:04 -0700
> From: Dale Hall <Dale.Hall-at-trw-dot-com>
> To: Tesla List <tesla-at-pupman-dot-com>
> Subject: RE>Re: Testing capacitors (
> 
> RE>Re: Testing capacitors (fwd)
> Terry P,
> What are your Xray cap specs/mfr ?  
> I have 4ea .01 80kV BYCAP, Inc which are Polypropylene/Al foil tab to
screw
> vacuum oil filled.  The only deficiency may be the connections to the
screws
> - could be beefier for high discharge currents (for which they weren't
designed)
> but should work OK. I spoke to the owner about a year ago - Ken Yihiro
> at 800 322-9227.  The Caps were custom for a GE Xray V-multipy applic.
> Mine are housed in brown phenolic, 6A803-103CA, mfrd 8/90 in Chicago,
ILL.
> Dale
> ------------------------------
> Date: 7/27/98 8:38 PM
> To: Hall, Dale
> From: List, Tesla
> 
> 
> 
> ---------- Forwarded message ----------
> Date: Mon, 27 Jul 1998 17:19:38 -0700
> From: Terry Perdue <terryp-at-halcyon-dot-com>
> To: tesla-at-pupman-dot-com
> Subject: Re: Testing capacitors
> 
> (I posted this recently, but received no replies, except one asking me
not
> to post in HTML, which may have made it unreadable to some. Now that I've
> figured out how to turn that off, I'll ask my dumb questions again):
> 
> I posted a message a few weeks ago about some oil-filled 10nF 80kvdc
"xray
> machine" caps I have, asking if they might be suitable for TC use.
Several
> people thought it was worth a try, but suggested a safety enclosure, in
case
> they overheated and exploded. My question is this:
> 
> Is there a way I can test them for suitability before building the whole
> system? I have a NST, and could fashion a temporary spark gap. I'd like
to
> run a minimal system long enough to give me confidence that these caps
will
> survive before going any further, as I'm not interested in rolling my own
> cap.
> 
> Two other questions:
> 
> I had hoped to use 10" diam acrylic tubing for the secondary, but at
$40/ft,
> may have to use PVC. But I'm considering getting some sheet acrylic and
> melting it around a form, possibly in half-cylinder sections, then
cementing
> them together. I've been pretty successful forming plexiglas in this way
in
> the past, and assume that it is the material of choice. Has anyone tried
> this? (I'm assuming that the sheet stock is much less expensive.)
> 
> Finally, I think I read that if the spark gap is close enough to the
> transformer, secondary RF suppression isn't necessary. Is there agreement
on
> this?
> 
> Thanks for your comments.
> 
> Terry Perdue
> 
> 
>