[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]
Here are my current specks: Was I give up!
Ok, I read a lot of replies and lots of people asked what my coil
configuration was.
Ok, here it is. As I mentioned before, I built it according to plans from
sciencefirst-dot-com but
it did not work as advertized (Oh what a surprise).
NST is the same in all cases 9,000 volt at 30 MilliAmps
Given this NST, I caculate the Impedance as being 300,000 ohms
I caculate that I need an .088pf capacitor or since I have two in series, I
will need two about
176uf each.
My current caps are aluminum flashing stacked with two 12mm sheets of poly
between them. The plates
are such that there is 6.5 inches of overlap. the sheets are 4" wide so I
caculate an area per plate
of 26 square inches.
Using the formula I saw in Brent Turner's book and given the thickness, I
calculate that I need
35 sheets.
Primary is #14 wire, about 40 windings with lots of bare spots for tapping.
Secondary is a 3" PVC pipe covered with 24 inches of #29 wire.
There are three chokes composed of #29 wire wrapped over a half inch thick
dowel. The length of the
windings are all 3.5" each. One choke on each high voltage lead from the NST
between the spark gap
and the NST. The caps are in series with the primary winding and the other
end goes to one side of
the spark gaps. This isolates the primary from the rest of the circuit as
far as the 60 cycle current
is concerned. The primary is center tapped in the center after tuning
through a third choke with the
same configuration as the other two.
My best performance was off a spark gap composed of flashing rolled up at
the ends that was mounted in
a 4" PVC joint with a muffin fan on top.
I had about 12-14" sparks and similar streamers off this with a 2" X 8"
commercial spun aluminum
toroid.
One person here said given what I had, I should not have trouble getting 30"
sparks.
In each case where I had a degradation of performance when I tried to change
the spark gap I
observed a drastic loss in performance. In each case, I tried different
things to make the new
spark gap to work even romotely as well as the original all failed. Attempts
to revert to the
original gap design mentioned above resulted in performance that was not
quite what I had before
I tried to change it. Over a period of several attempts the output of the
coil seemed to deminish as
each attempt to successfully resulted in failure and attempts to revert,
ended up in more failure.
Finally, I tried two brass doorknobs. Flat surface area inside the same PVC
joint with the same fan.
Result was a significant improvement in performance to the tune of 16"
sparks. The best yet!!
The next morning, I turned it on and the gap would only fire sporatically.
So, I closed the gap a bit
and by the time I got some reliable firing the sparks were quite a bit
weaker. They were thinner and
much shorter, with less bang and noise from the toroid.
The spark gap too sounded different. It had a rat tat tat sound that was
noticeably slower and only
half of normal volume. Before the failure, the spark gap was quite loud with
a rapid sound similar to
a chainsaw.
I tore open the caps that had 17 plates each - According to the
calculations, I need 35 plates each
because they are in series but I noted that the more plates I added the
weaker the system seemed to
become. I inspected each plate carefully, and there was NO sign of any break
through the electrolyte.
After trying to work with it today and tune it more and trying to increase
the number of plates I got
some better performance but the gap simply does not have the loud BANG it
had before, tho the frequency
seems back to normal. The spark length is about 8" but are half as loud, and
only half as thick as they
were before. Streamers are also thinner but more of them, the streamer
length is only 3 or 4 inches max
compared to 15" or so streamers the night before they failed.
It does not seem to make sense to me that the closer I come to the supposed
35 plates each cap, the
less performance there is. There is something wrong but I don't know what it
is.
Can someone confirm the above calculations for me? I am prone to error to a
most astonishing degree
and I don't trust my calculations any farther than I can throw a fully
loaded and operating washing
machine! I transpose figures, I fail to see stuff that is right in front of
my face and am capable
of great overvation and the next I can act like I never had an eye or a
braincell to my name.
My guess as to what is wrong is that the NST has fried partially and I am
not getting the current
I should be getting out of it.
The second guess is that somehow the ozone had rendered the electrolyte in
the caps as conductive
but it is hard for me to believe that this can happen over night.
As for getting a new neon sign transformer, this is rather problematic as
the only shop that has any was
recently bought by "Newbies" who said themselves that they do not have a
clue of what the value
of anything they have in their inventory and seemed understandably reluctant
to sell or give away any
used items.
You should know that I live in an Apartment. There are no garages. So, I
have nothing but hand tools at
my disposal and I must eyeball things to make sure they are parallel as best
I can. I'm not terribly
accurate due to a history of near blindness that was left untreated so long
as a child that my depth
perception is only 10% of normal. I do what I can, but having even a table
saw is totally out of the
question in this apartment.
I wish I could hope that I havent' forgotten anything but I know for certain
that I have.
It never fails. At least I got a nice video of my tesla coil operating well
and frying some nasty
meat bees before it died or became severely ill.
My next step, is to start stripping off a plate on each cap, and
reassembling and retuning and trying
it out until I either note a decrease or a plateau in performance. I think I
need LESS plates not more
I used to use doorknob caps. Boy those things created some lovely output. I
wish I could get my hands
on some of those. Sure they wern't the best but they beat the stuffins out
of whatever other
failed caps I tried.
I would appreciate any help. I thank you all. I note that nobody flamed me.
This I bet would never
happen in any discussion group as most other groups are more like a pack of
wolves that jump another
when one of them go down. I am most impressed with the kind and never harsh
replies I got from this
group. You should all be proud.