I'm curious, what are the dangers of running an ASYNC gap with a large
(pole pig) setup? I'd always heard it was damaging to caps, etc. Is it
acceptable to run totally async and not have to worry about destroying caps?
On Sun, Feb 25, 2018 at 4:15 PM, David Rieben <drieben@xxxxxxx> wrote:
> Yes, I concur with John's assessment of the sync vs. async debate. I
> experienced the very thing that John referred to where my output spark
> length deminished after converting my sync SG over to sync. Just as he
> mentioned, I left the original STR (0.1 uFd) primary cap unchanged. Since
> we are talking about a pole pig fired beast, it has proven far more
> practial (and economical) for me to remain async with my system, as big
> bright sparks were my goal, anyway. A truly LTR cap, whose voltage standoff
> and capacitance can match up with a 14,400 volt,10 or 15 kVA rated pole pig
> in sync operation would have to be a real monster (> 0.3 or 0.4 uFd @ 25
> kVAC or 60 kVDC) and a real drain to the typical hobbiest's budget!
>
> Probably the only type of TC drive sytem that could possibly complete with
> or possible beat the asnc rotary gap for pole pig fired coil systems of
> equivalent power levels, whose endgame is the biggest and brightest sparks
> possible, would be the DC resonant system. Of course, the required giant
> storage cap(s) - (up to several 10's of uFds @ >20 kVDC) and ultra fast
> recovery, high voltage diodes also render this approach considerably more
> pricey that the standard async system, too.
>
> Sync RSG with LTR primary caps is the best way to coax maximum spark
> length from the limited available power, while at the same time going
> easier on the fragile HV side windings of (an) NST(s), though.
>
> David
>
>
> ----- Original Message ----- From: "Futuret via Tesla" <tesla@xxxxxxxxxx>
> To: <tesla@xxxxxxxxxx>
> Sent: Sunday, February 25, 2018 9:52 AM
> Subject: Re: [TCML] Best Spark Gap for NSTs?
>
>
> The answer is not simple or direct. There are advantages and
>> disadvantages for sync or non-sync.
>>
>>
>> Did you happen to try
>> feeding the motor with 140V from a step up type variac?
>> Often this will keep it in sync. If you created flats on
>> the rotor that are at least 1/4 the width of the full rotor diameter,
>> that is enough metal to remove. Some small motors
>> are very wimpy and don't work well such as small
>> shaded pole fan motors. And of course you should
>> have 4 flats on your motor.
>>
>>
>> Yes the preferred break rate has a lot to do with it.
>> Sync operation is most beneficial at low break rate
>> of 120 bps. However it's absolutely necessary to
>> use a large enough capacitor to take advantage of
>> this. Back in the "day", a lot of people were installing
>> a sync gap onto their TC and getting worse results
>> because they were using a small capacitor with
>> a static gap previously. They left the small
>> capacitor in place and therefore saw a reduction
>> in spark length when they installed the sync rotary
>> gap.
>>
>>
>> For anything over 120 bps, sync doesn't really
>> help, you might as well use non-sync or a static
>> gap. Gary Lau posted some information about
>> the best capacitor sizes for sync or non-sync, etc,
>> in the past and I guess this is at his website. Also
>> JavaTC might give some information about the
>> best capacitor values for sync or non-sync, for
>> NST powered coils.
>>
>>
>> 120 bps sparks will not be quite as bright as
>> higher breakrate sparks. Also they tend not
>> to create the kind of long tendrils that can
>> form at higher breakrates. Certain coils
>> tend to show these long thick tendril
>> type sparks.
>>
>>
>> John
>>
>>
>>
>> -----Original Message-----
>> From: Daniel Kunkel <dankunkel@xxxxxxxxx>
>> To: Tesla list <tesla@xxxxxxxxxx>
>> Sent: Sun, Feb 25, 2018 9:45 am
>> Subject: [TCML] Best Spark Gap for NSTs?
>>
>> I modified a 1725 rpm motor to run in salient pole operation years ago. It
>> will seek and then lock into phase and then break out again. I think I
>> recall reading that if you don't remove enough rotor material it will
>> seek.
>> If you remove too much it will over heat.
>>
>> So before to I take this back to machining, is it even worth it? What is
>> the best gap for NSTs? Is SRSG is the answer what is the preferred break
>> rate?
>>
>> ~Dan
>> To synch or not to synch
>> Kansas City area
>> _______________________________________________
>> Tesla mailing list
>> Tesla@xxxxxxxxxxxxxxxxxx
>> https://www.pupman.com/mailman/listinfo/tesla
>>
>> _______________________________________________
>> Tesla mailing list
>> Tesla@xxxxxxxxxxxxxxxxxx
>> https://www.pupman.com/mailman/listinfo/tesla
>>
>
> _______________________________________________
> Tesla mailing list
> Tesla@xxxxxxxxxxxxxxxxxx
> https://www.pupman.com/mailman/listinfo/tesla
>
--
Chris Boden
President
The Geek Group National Science Institute
www.thegeekgroup.org
--
This email may contain confidential and privileged material for the sole
use of the intended recipient. Any review or distribution by others is
strictly prohibited. If you are not the intended recipient please contact
the sender and delete all copies.
_______________________________________________
Tesla mailing list
Tesla@xxxxxxxxxxxxxxxxxx
https://www.pupman.com/mailman/listinfo/tesla