[Home][2015 Index] Re: [TCML] No topload output [Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

Re: [TCML] No topload output



Ok, I ended up adding a temporary winding to the primary coil (at present I believe I am at about 8.25 turns on the primary.  But things are looking up.  When I first put the ground wire up near the toroid I was only able to get about 2" sparks.  I think I was at about 4.5 turns at that point. 

It seems that I may still need to add more turns to get it really dialed in, but I noticed that having the ground wire 11" from the toroid I was getting good arcing, but when I tried to move it to 12" away from the toroid I could reach it once in a while but then I got a lot of action on my safety gap.  I'm thinking I might need to move that safety gap apart a little bit more. I don't want to move the safety gap out so far that I my spark gap might get too wide as I thought I read that a spark gap too wide can burn up an NST.

Here's a video of the 11" arcing:  https://youtu.be/Lka24-Hqf3k

Thanks!   Paul
--------------------------------------------
On Sun, 12/27/15, Heather & Paul Novotny via Tesla <tesla@xxxxxxxxxx> wrote:

 Subject: Re: [TCML] No topload output
 To: "Tesla Coil Mailing List" <tesla@xxxxxxxxxx>
 Date: Sunday, December 27, 2015, 9:08 PM
 
 Hi Jim,
 
 I do have about a 2" gap in my Strike Rail.
 
 Good idea to run a solid copper wire from ground up next to
 the toroid and a having breakout point on the toroid to see
 if anything is happening up there.
 
 I have the coil on the floor of my garage which is a cement
 slab poured on earth.   My ground is a copper
 wire that runs to a metal stake pounded down about 2.5 feet
 into the earth outside my garage.
 
 Thanks!
 
 Paul
 --------------------------------------------
 On Sun, 12/27/15, Jim Lux <jimlux@xxxxxxxxxxxxx>
 wrote:
 
  Subject: Re: [TCML] No topload output
  To: "Heather & Paul Novotny" <p_novotny@xxxxxxxxx>,
 "Tesla Coil Mailing List" <tesla@xxxxxxxxxx>
  Date: Sunday, December 27, 2015, 9:02 PM
  
  On 12/27/15 5:29 PM,
  Heather & Paul Novotny via Tesla wrote:
  >
  Hi guys,
  >
  > I just
  tried my TC for the first time tonight after COUNTLESS
 hours
  of work on it.  Unfortunately, I am getting no streamers
  from the topload.
  >
  
  Do you have a breakout point
  on the topload?
  And something to spark to? I
  use a piece of grounded (as in connected to 
  the bottom of the secondary/counterpoise)
  copper tubing  that sticks up 
  and I can
  move closer and farther from the topload.
  
  In your picture, I'd put
  it sticking up from the edge of your cart, 
  until you get things working.
  
  
  Does your
  strike rail have a gap in it? (It should, or it looks like
 a
  
  shorted turn)
  
  What's your ground scheme look like? For a
  coil this size, I'd use 
  something like
  a 3-4 foot square piece of chicken wire or hardware 
  cloth, or sheet metal under the coil.  (rule
  of thumb is that "ground" 
  should
  have a radius comparable to the height of the
 secondary). 
  In 
  your case, that ground
  screen/counterpoise should be at the level of the 
  top of your cart.
  
  
 _______________________________________________
 Tesla mailing list
 Tesla@xxxxxxxxxx
 http://www.pupman.com/mailman/listinfo/tesla
_______________________________________________
Tesla mailing list
Tesla@xxxxxxxxxx
http://www.pupman.com/mailman/listinfo/tesla