Makes sense. As a local government who spent thousands a month, we probably got the deeper discount.
________________________________
From: "mddeming@xxxxxxx" <mddeming@xxxxxxx>
To: tesla@xxxxxxxxxx
Sent: Wednesday, March 5, 2014 9:41 PM
Subject: Re: [TCML] Base
It has been my experience with our local Grainger's that they give deep discounts to corporations, moderate discounts to licensed contractors who are "regulars" small discounts to licensed "drop-ins" and full retail to casual buyers. So it seems that whether they are competitive in price or not depends on whose money you're spending and how often.
Matt D
-----Original Message-----
From: Yurtle Turtle <yurtle_t@xxxxxxxxx>
To: Tesla Coil Mailing List <tesla@xxxxxxxxxx>
Sent: Wed, Mar 5, 2014 3:39 pm
Subject: Re: [TCML] Base
Depends on what you're buying. I spent nearly 24 years buying industrial
stuff...
________________________________
From: rlddomsicz <rlddomsicz@xxxxxxx>
To: Tesla Coil Mailing List <tesla@xxxxxxxxxx>
Sent: Wednesday, March 5, 2014 7:30 AM
Subject: Re: [TCML] Base
Not in my experience.
----- Original Message -----
From: "Yurtle Turtle" <yurtle_t@xxxxxxxxx>
To: "Tesla Coil Mailing List" <tesla@xxxxxxxxxx>
Sent: Monday, March 3, 2014 10:48:41 PM
Subject: Re: [TCML] Base
Grainger is often cheaper than McMaster Carr.
________________________________
From: Jason Johnson <jasonmsusolar@xxxxxxxxx>
To: Tesla Coil Mailing List <tesla@xxxxxxxxxx>
Sent: Monday, March 3, 2014 8:30 AM
Subject: Re: [TCML] Base
Polypropylene is another excellent choice.
I find McMaster to be an excellent source for small sized pieces. Not
usually the cheapest, but typically competitive.
http://www.mcmaster.com/#standard-polypropylene-sheets/=qxl3vu
Of course they have UHMW as well, but I think PP is cheaper.
- Jason
On Sun, Mar 2, 2014 at 3:08 PM, Jim Lux <jimlux@xxxxxxxxxxxxx> wrote:
> On 3/2/14 11:42 AM, t-burns14 wrote:
>
>> I have an opportunity to use a CNC milled piece for my base, as seen
>> in one of the Geek Group videos. The milled a spiral into the piece
>> of plastic and then just hammered the tubing into the spiral cutout.
>> I'm wondering what material would be good for that. They might have
>> been using High Density Polyethylene, because I remember them saying
>> it was food grade and polyethylene is used for cutting boards. Any
>> insight? Thanks
>>
>>
> It probably *was* a HDPE cutting board, unless they happened to have a
> source for HDPE scrap. Otherwise, you're buying a 4x8 foot sheet of the
> plastic.
>
> HDPE cutting boards are readily available in a variety of useful sizes,
> and are cheap. There are also polycarbonate cutting boards.
>
> _______________________________________________
> Tesla mailing list
> Tesla@xxxxxxxxxx
> http://www.pupman.com/mailman/listinfo/tesla
>
_______________________________________________
Tesla mailing list
Tesla@xxxxxxxxxx
http://www.pupman.com/mailman/listinfo/tesla
_______________________________________________
Tesla mailing list
Tesla@xxxxxxxxxx
http://www.pupman.com/mailman/listinfo/tesla
_______________________________________________
Tesla mailing list
Tesla@xxxxxxxxxx
http://www.pupman.com/mailman/listinfo/tesla
_______________________________________________
Tesla mailing list
Tesla@xxxxxxxxxx
http://www.pupman.com/mailman/listinfo/tesla
_______________________________________________
Tesla mailing list
Tesla@xxxxxxxxxx
http://www.pupman.com/mailman/listinfo/tesla
_______________________________________________
Tesla mailing list
Tesla@xxxxxxxxxx
http://www.pupman.com/mailman/listinfo/tesla