[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

RE: [TCML] NST and HV Cables



Binny wrote "curious how you came up with the 10KV value. Looking at the
nameplate under KV I see 3,75-3,75 and that leads me to believe it is a
7,500 volt 60 MA output not 10/60.  "

Bimmy: Pour yourself a drink, sit down and relax, and re-read my post again,

Rixong: Yes it appears to be a heavy iron type even though it looks like a
new type electronic one. The trouble though is that the sensors for earth
leakage and open-circuit protection will cause problems. Now, if you can
actually disconnect them it would be ok, but a lot that look like that have
the parts buried inside the resin, the FART one you have fortunately didn't.

Later resin filled ones without the protection circuitry, could be better in
some respects, as a modern resin would be better than old fashioned tar of
course, which may have voids in it. Tar is also probably a worse insulator
than modern resin. 
I used four 10Kv FARTS the same as yours in parallel for quite a while
before getting a pig.

Phil


-----Original Message-----
From: tesla-bounces@xxxxxxxxxx [mailto:tesla-bounces@xxxxxxxxxx] On Behalf
Of Binny
Sent: 19 October 2011 18:23
To: Tesla Coil Mailing List
Subject: Re: [TCML] NST and HV Cables

Hello Phil and group,
                                    Say Phil, just curious how you came up
with the 10KV value. Looking at the nameplate under KV I see 3,75-3,75 and
that leads me to believe it is a 7,500 volt 60 MA output not 10/60.  From
what I have read it will work,not the best and hard on the spark gap but it
is doable. I wonder tho ,if a voltage doubler would work in this
circumstance. I have at least one 750/120 and wanted a simpler demo version
so I put it on the back burner so to speak. A set up like that might be an 
interesting coil project.   ...Happy coling to all...Binny----- Original 
Message -----
From: "Phil Tuck" <phil@xxxxxxxxxxx>
To: "'Tesla Coil Mailing List'" <tesla@xxxxxxxxxx>
Sent: Wednesday, October 19, 2011 11:49 AM
Subject: RE: [TCML] NST and HV Cables


> Yes and Yes.
>
> A lot of resin NST's can't be used, but I have used that same NST 
> successfully. The GFI thing on those is external and screws across 
> three of the terminals on the top, but yours is missing. The lid 
> normally has two metal links that engage with the springs you can see, 
> the idea being you pull the lid off and the HV is then off. It's a bit 
> low on output volts as 10Kv would be better (10Kv is the max in Europe 
> I think, while America has 15Kv ones)
>
> Careful when you wire it up as the HV outputs are at the top part in 
> the picture.
>
>
> Phil
>
>
> -----Original Message-----
> From: tesla-bounces@xxxxxxxxxx [mailto:tesla-bounces@xxxxxxxxxx] On 
> Behalf Of Rixong
> Sent: 19 October 2011 16:22
> To: tesla@xxxxxxxxxx
> Subject: [TCML] NST and HV Cables
>
> Hello! We are three young students from Sweden about to do a project 
> that involves the construction of a tesla coil. Since we are all 
> beginners when it comes to constructing tesla coils we will post a lot 
> of basic questions which we don't think will be a problem for you guys to
answere.
>
> So, here is our first question. Will this neon sign transformer work 
> as a power supply for a tesla coil?
>
> http://i52.tinypic.com/20u7bb5.jpg
> http://i52.tinypic.com/103ewr8.jpg
>
> Second question. Are these high voltage cables suitable for a tesla coil?
>
> http://i55.tinypic.com/9gy4pv.jpg
> _______________________________________________
> Tesla mailing list
> Tesla@xxxxxxxxxx
> http://www.pupman.com/mailman/listinfo/tesla
>
> _______________________________________________
> Tesla mailing list
> Tesla@xxxxxxxxxx
> http://www.pupman.com/mailman/listinfo/tesla
>
> 

_______________________________________________
Tesla mailing list
Tesla@xxxxxxxxxx
http://www.pupman.com/mailman/listinfo/tesla

_______________________________________________
Tesla mailing list
Tesla@xxxxxxxxxx
http://www.pupman.com/mailman/listinfo/tesla