[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

Re: [TCML] newer tesla coil parts (split Terry filter resistors)



Gary:

Interesting question.

I was also wondering the precise requirement for the spark gap balls.  In
the days before varisters came along we definitely used them.  But, now, the
varisters should shunt any overpotentials to ground directly, essentially,
make the spark gap balls unnecessary as there should not be any high
potentials present to fire the gaps.

I would assume this might be of assistance in the rare event of horrible
mis-tuning, but with JAVATC this has almost become a thing of the past.  I
usually add 1/4 turn beyond JAVATC predicted pri tap point, and it's dead-on
at full power levels for most small and medium size coils.

Comments on this idea (eliminating the spark gaps) welcome.

Dr. Resonance




On Thu, Nov 12, 2009 at 9:22 AM, Lau, Gary <Gary.Lau@xxxxxx> wrote:

> I'm not sure I see the value in having the caps & varistors at the midpoint
> of the resistors.  The R-C filter will only see one half of the resistance,
> so its low-pass frequency will be twice as high.  The only benefit I see to
> this is the bypass caps will be cushioned against the discharge current when
> the safety gaps fire.  But given that this should not be a frequent
> occurrence, I'm not sure this is worth compromising the R-C filter's cutoff
> frequency for.
>
> While splitting the 1K between two 500Ohm units is fine, I think it is bad
> advice to suggest placing the caps at the midpoint.
>
> Regards, Gary Lau
> MA, USA
>
> > -----Original Message-----
> > From: tesla-bounces@xxxxxxxxxx [mailto:tesla-bounces@xxxxxxxxxx] On
> > Behalf Of Jim Mora
> > Sent: Tuesday, November 10, 2009 3:30 AM
> > To: 'Tesla Coil Mailing List'
> > Subject: RE: [TCML] newer tesla coil parts
> >
> > Hi DC, All,
> >
> > I agree - nice, thoughtful construction! It never even occurred to me
> split
> > the halves.
> > We will all look forward to more pictures of our art form at work!
> >
> > Jim Mora
> >
> > -----Original Message-----
> > From: tesla-bounces@xxxxxxxxxx [mailto:tesla-bounces@xxxxxxxxxx] On
> > Behalf
> > Of DC Cox
> > Sent: Monday, November 09, 2009 2:46 PM
> > To: Tesla Coil Mailing List
> > Subject: Re: [TCML] newer tesla coil parts
> >
> > Nice construction work.
> >
> > Both Digi-Key and Mouser usually stock them.  I split mine into two 50
> watt,
> > 500 Ohm resistors putting one ahead and one behind the common
> varister/cap
> > connections.
> >
> > D.C. Cox
> >
> >
> >
> >
> > On Mon, Nov 9, 2009 at 10:53 AM, Shaun Epp <scepp@xxxxxxx> wrote:
> >
> > > Here are some pictures of my new NST filter.  I ordered parts from
> digikey
> > > this time and used the correct values and MOVs( before I was using
> 3Kohm
> > > resistors and door knob caps).  It's built so that I can change from 7
> > MOVs
> > > per side to 8.  After reading posts on this list, I think I'm going to
> use
> > > all 8 for my 12Kv, 60mA NST because it puts out more that 12Kv at 120V
> in
> > > and I'm using a variac.  I'm using 50 watt resistors for the 1Kohms, I
> > can't
> > > get ahold of the 100w versions, does anyone on the list have some for
> > sale?
> > >
> > > http://i487.photobucket.com/albums/rr239/growl99/NSTfilterfront.jpg
> > >
> > > http://i487.photobucket.com/albums/rr239/growl99/NSTfilterback.jpg
> > >
> > >
> > > Question:
> > > My capacitor bank is currently on 2 boards and I'm going to make a 3rd
> > > board of CD 942 caps (14 caps 0.15uf in series spaced).  What are other
> > > coilers using for board to board spacers?, I want to stack them one on
> top
> > > of the other, and legs to keep them off of the floor,  right now I'm
> using
> > > 1/4 inch nylon bolts with heat shrink tubing over them to strengthen
> them.
> > >
> > > thanks,
> > >
> > > Shaun Epp
> > >
> > > _______________________________________________
> > > Tesla mailing list
> > > Tesla@xxxxxxxxxx
> > > http://www.pupman.com/mailman/listinfo/tesla
> > >
> > _______________________________________________
> > Tesla mailing list
> > Tesla@xxxxxxxxxx
> > http://www.pupman.com/mailman/listinfo/tesla
> >
> > _______________________________________________
> > Tesla mailing list
> > Tesla@xxxxxxxxxx
> > http://www.pupman.com/mailman/listinfo/tesla
> _______________________________________________
> Tesla mailing list
> Tesla@xxxxxxxxxx
> http://www.pupman.com/mailman/listinfo/tesla
>
_______________________________________________
Tesla mailing list
Tesla@xxxxxxxxxx
http://www.pupman.com/mailman/listinfo/tesla