[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

Re: [TCML] still stuck at 36



I think what makes a hyperbaric gap perform well is that it's
a single gap.  This makes it a low loss gap.  Once you have a
low loss gap then all that's needed is to quench it adequately.
Since a single gap is harder to quench than a multi-gap, this
is why a good amount of air flow is needed.

The air flow is
also needed to cool the electrodes.  If there's not enough
air flow the gaps may run too hot and may begin to power arc,
or quench very sluggishly.  If a gap quenches too slowly,
then less time is available to recharge the capacitor and
output suffers.

If there's too much air, then
the gap may fire intermittently with a sort of stuttering
action and this cuts the spark length too.  It's not really
over-quenching, it's simply erratic firing in the first place.
It's not that the gap quenches too fast, rather it's that
the gap does not fire consistently.

John
--


-----Original Message-----
From: DC Cox <resonance@xxxxxxxxxxxx>
To: Tesla Coil Mailing List <tesla@xxxxxxxxxx>
Sent: Tue, 27 Jan 2009 4:58 pm
Subject: Re: [TCML] still stuck at 36



It's not clear why to me either. My best guess is better cooling due to the
high velocity air, and perhaps increased turbulence
around the ends of the copper pipes.

I know that most coils performance jumps in amazing quantity of spark output
when the hyperbaric gap is used.  I have never used it above 4 kVA as a
single gap, but did some experiments at 7 kVA with a dual series hyperbaric
gap and it seemed to work as good as a small rotary.

Perhaps looking at scope ringdowns with and without a hyperbaric gap might
provide some clues.

Dr. Resonance




On Tue, Jan 27, 2009 at 1:51 PM, Lau, Gary <Gary.Lau@xxxxxx> wrote:

I don't disagree that hyperbaric gaps work well, but I'd like to be
clear
on why. Too often on this List, the word "quenching" is used
incorrectly.
My measurements showed conclusively that hyperbaric gap losses were
lower
than in a sucker gap, but I made no attempt to measure actual
quenching.
Quenching is unrelated to gap losses and refers to how many pri-sec
energy
trades occur before the gap extinguishes. In fact, I think that
typically,
lossy gaps (at least multi-segment gaps) have superior quenching.

So, have you seen evidence that actual quenching, as observed on a
scope,
was superior with the hyperbaric gap? Was this with free-air
streamers or
grounded (connected) streamers?  Seems like a very difficult thing to
accurately compare between two systems.

Regards, Gary Lau
MA, USA

> -----Original Message-----
> From: tesla-bounces@xxxxxxxxxx [mailto:tesla-bounces@xxxxxxxxxx] On
> Behalf Of DC Cox
> Sent: Tuesday, January 27, 2009 1:31 PM
> To: Tesla Coil Mailing List
> Subject: Re: [TCML] still stuck at 36
>
> Bill:
>
> What was your maximum spark before you used the hyperbaric sparkgap?
>
> Also, put a variac on the vac. cleaner motor, and fine adjustment
of the
> speed will increase your output even more.  Usually best output
> around 75% of the variac.
>
> I know they work great.  They always increase your sec spark output
> dramatically which means we have been underquenching
> with most of our previous designs.
>
> Dr. Resonance
>
>
>
>
> On Tue, Jan 27, 2009 at 5:50 AM, Bill Bohn <b.jbohn@xxxxxxxxxxx>
wrote:
>
> > I built the hyperbaric gap as described WOW!Now I get 44" I am
using a
shop
> > vac for suction.I am using 5 of the 6 strings of caps.I think I
did
some
> > damage
> >
> > To my 5-1/4 coil.Now I have a 6.625" secondary wound 26.5" 1060
turns.
Top
> > load is 4.5x18 toroid and a 7" sphere.Seems best with the primary
clamped
> >
> > At turn 5.The spark sounds somewhat eratic and choppy.IT will
smooth
out
> > some by adjusting the spark gap closer at the loss of streamer
length .
> >
> > What is the method of measuring BPS?IT doesn't seem to sound
right.The
> > coupling between primary and secondary is 0.I am going to put the
6
strings
> > of
> >
> > My mmc cap in but I think it will be best tuned at about turn 2
and
become
> > even more erratic.
> >
> > I am getting positive results and thank everyone for all the
ideas and
2
> > cents worth.
> >
> > _______________________________________________
> > Tesla mailing list
> > Tesla@xxxxxxxxxxxxxx
> > http://www.pupman.com/mailman/listinfo/tesla
> >
> _______________________________________________
> Tesla mailing list
> Tesla@xxxxxxxxxxxxxx
> http://www.pupman.com/mailman/listinfo/tesla
_______________________________________________
Tesla mailing list
Tesla@xxxxxxxxxxxxxx
http://www.pupman.com/mailman/listinfo/tesla

_______________________________________________
Tesla mailing list
Tesla@xxxxxxxxxxxxxx
http://www.pupman.com/mailman/listinfo/tesla

_______________________________________________
Tesla mailing list
Tesla@xxxxxxxxxxxxxx
http://www.pupman.com/mailman/listinfo/tesla