Re: [TCML] Trans-cap uf matching, over/under?

[johnbrooks@xxxxxxxxxxx]

Yes and a coupla nice single,almost unbranched streamers,that I like so
well.
Very nice.
Joe in Texas

On Thu, 31 Dec 2009 04:16 -0500, "Dave Goodfellow"
<dgoodfelo@xxxxxxxxxxx> wrote:
> I have been fond of using under resonant capacitor values, especially 
> for small transformers. The transformer fires so fast that I don't think 
> that there is much potential for it to get hurt. It also produces a 
> pleasing tone that I prefer,  to the rat-a-tat-tat sound of a coil with 
> a larger capacitor load on the transformer. Be prepared to use a lot 
> more turns on your primary with those smaller capacitor values. That 
> being said, I have found that a 15/30 combined with a .0075 capacitor 
> works very well. I like to use a 4" x 20" coil with 1400 turns on it, 
> and about 20 turns on the primary. My turns are closely spaced 8 ga 
> solid copper bare ground wire. A 13" to 15" o.d. toroid will use up all 
> the turns on the primary. I have seen sparks in the 30" range using such 
> a setup, combined with a simple fan cooled single spark gap set to 7/32"
> 
> If you go to this link, you will see a small coil I had on ebay last 
> year. It had a less-than-resonant capacitor value on it, but I don't 
> remember the exact capacitance. I incorrectly stated that it had 
> phenolic primary holders, when it has polyethylene blocks.
> http://www.youtube.com/watch?v=UwmMCaMmRmU
> 
> Dave Goodfellow
> 
> Brian Hall wrote:
> > I have a 15kv/30ma NST so the ideal capacitance is .0053 uf, but since I don't want it to match impedance with the transformer and risk frying out a leg, I have read that 1.3 to 1.4 x that capacitance is desirable, aka LTR (larger than resonant ... impedance)
> >
> >  
> >
> > So, that would give me a range of .0068 to .0074 uf for the tank capacitor (at around 30 to 40 kv)
> >
> >  
> >
> > My question is how would the performance be affected if I were to use 0.011 uf (a hair over 2 x resonant impedance)?   
> >
> >  
> >
> > And what would happen if I go a bit under it, such as .0033 uf?  What effect would that have on the TC circuit or even the hv transformer?  Would it hurt anyting?
> >
> >  
> >
> > Lastly, if I were to connect 2 NSTs of the same value in parallell, such as two 15/30 NSTs, to basically get one 15/60 power supply, would the calculation for the impedance of the 2 NSTs of Z = E / I (to find the cap value) be the same as if I had a single 15/60 NST?  if it were, then .011 uf would be a hair above resonance with the transformer, but not as high as 1.3 x above it ... 
> >
> >
> >
> > ---------------------------------- 
> > Brian Hall 
> >
> >
> >
> >
> >  		 	   		  
> > _________________________________________________________________
> > Hotmail: Free, trusted and rich email service.
> > http://clk.atdmt.com/GBL/go/171222984/direct/01/_______________________________________________
> > Tesla mailing list
> > Tesla@xxxxxxxxxx
> > http://www.pupman.com/mailman/listinfo/tesla
> >
> >   
> _______________________________________________
> Tesla mailing list
> Tesla@xxxxxxxxxx
> http://www.pupman.com/mailman/listinfo/tesla
-- 
  
  johnbrooks@xxxxxxxxxxx

-- 
http://www.fastmail.fm - One of many happy users:
  http://www.fastmail.fm/docs/quotes.html

_______________________________________________
Tesla mailing list
Tesla@xxxxxxxxxx
http://www.pupman.com/mailman/listinfo/tesla