[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

Re: MMC Question.



Original poster: "Glen McGowan" <glen.mcgowan@xxxxxxxxx>

Nevermind... is see what i was missing....The 940c and the STK's I have are identical. The 942C's are the higher current caps. I was meshing the two previous responses together. Scott was comparing the STK's to the 942C and Terry was comparing the 940C to the STK.


Surely the STK's would be about to handle 900W?


On 8/8/06, Tesla list <<mailto:tesla@xxxxxxxxxx>tesla@xxxxxxxxxx> wrote:
Original poster: "Glen McGowan" <<mailto:glen.mcgowan@xxxxxxxxx> glen.mcgowan@xxxxxxxxx>

Thanks for the extra effort regarding the caps.

Regarding the peak current, both Charts show the same values for peak
current. I must be missing something(?). I'm not building a beast by
any means. But,this is my first coil and plan to power it with a
15/60 NST. My MMC will use 16 of the STK's in series.

Wouldn't the current remain at 60mA throughout the tank?

I'm all ears, still learning so everything is educational at this
point. As long as I don't stop my heart I consider it a learning
experience. I would like to avoid the "power up and run for the
hills" avenue as much as possible.

On 8/7/06, Tesla list <<mailto: tesla@xxxxxxxxxx><mailto:tesla@xxxxxxxxxx>tesla@xxxxxxxxxx> wrote:
Original poster: Vardan
<<mailto:vardan01@xxxxxxxxxxxxxxxxxxxxxxx ><mailto:vardan01@twfpowerel ectronics.com>vardan01@xxxxxxxxxxxxxxxxxxxxxxx>

Hi,

I am a bit "concerned" about the STK caps.  One will note the specs here:

< http://www.stkelectronics.com/pdf/MP89.pdf>http://www.stkelectronics.com/pdf/MP89.pdf

And the specs for CD caps here as part number 940C20P15K-F:

<<http://cde.com/catalogs/940C.pdf>http://cde.com/catalogs/940C.pdf>http://cde.com/catalogs/940C.pdf

They are "exact duplicates"...  Now this stuff is not easy to measure
and "same setups" do not repeat even the next day!!!  So I worry
about "copying specs"...

But the raw materials are "commodities" and maybe they just "roll
them" just the same...

But the peak current is 1/3 and so they are not as "tough" as our
usual favorite capacitor...

Cheers,

          Terry




At 09:51 PM 8/7/2006, you wrote:
>Glen -
>
>Your questions about series vs. series-parallel connections have
>been answered, and you have been cautioned about the use of aluminum
>buss-bars as connection points. However, no one questioned your
>selection of capacitors. Your STK type MP89 utilize metallized-film
>construction. This type of capacitor uses an extremely thin layer of
>aluminum evaporated on to a polypropylene film as the capacitor
>"plates". This design has been shown to be marginal for Tesla coil
>use because of localized overheating and burning away of the end
>connections to the capacitor roll.. The type of capacitor
>construction recommended for use in Tesla coil tank circuits is
>film/foil, where the plate material is thin aluminum foil
>interleaved between the polypropylene dielectric film. This type of
>capacitor is well proven in Tesla coil use, while many people have
>experienced failures with the "metallized film" construction. Now if
>you design your MMC very conservatively, and calculate the peak
>current in your tank circuit, and make sure that your MMC has an
>appropriate current rating, you should be OK. However, for the best
>reliability and safety factor you should use film/foil capacitors.
>
>For instance, the Cornell-Dubilier Type 42C film/foil caps are very
>widely used in Tesla coils, and have gained an excellent reputation
>for reliability. The C-D type 942C cap of the same voltage and
>capacitance ratings as your STK caps (.15uF at 2,000 volts DC) has a
>peak current rating of 432 amps, and an RMS current rating of 13.5
>amps. Your STK caps have a peak current rating of 144 amps, and an
>RMS current rating of 8.9 amps. The CD cap has a peak current rating
>3X greater than the STK caps.
>
>Now if your STK caps were free, than just carefully design your coil
>so the peak primary current stays within the MMC's rating. Bear in
>mind that the C-D film/foil caps are available for under $3.00 each,
>and have a peak current rating 3X greater than the STK caps. Based
>on peak current rating, you should not have paid more than $1.00 per
>STK cap, or you would have been better off to go with the C-D type 942C caps.
>
>Post all the design specifications for your coil, and the list
>members will help perform a "design review" to verify that your MMC
>is appropriately matched to the rest of your system.
>
>Regards,
>Scott Hanson
>
>
>----- Original Message ----- From: "Tesla list"
<<mailto:tesla@xxxxxxxxxx> <mailto:tesla@xxxxxxxxxx>tesla@xxxxxxxxxx>
>To: <<mailto:tesla@xxxxxxxxxx><mailto:tesla@xxxxxxxxxx>tesla@xxxxxxxxxx>
>Sent: Monday, August 07, 2006 12:24 AM
>Subject: MMC Question.
>
>
>>Original poster: "Glen McGowan" <
<mailto:glen.mcgowan@xxxxxxxxx><mailto:glen.mcgowan@xxxxxxxxx>glen.mcgowan@xxxxxxxxx >
>>
>>Just received my new shiny bag of caps that Dr. Resonance kindly
>>provided. I got my fancy polycarbonate MMC perfboard fabricated.
>>But now that I got to thinking; what would be the best way to wire
>>them up? Option #1, would it matter if  I terminated *both* strings
>>to the same two pieces of metal at each end of the MMC? Or should I
>>go with Option #2 and keep them all in a strict series? Wouldn't it
>>still perform the same function in either scenario? Forgive the
>>newbie question I'm sure this is basic electronics.
>>
>>
>><< http://www.cyplexia.com/IM000525.JPG>http://www.cyplexia.com/IM000525.JPG>http://www.cyplexia.com/IM000525.JPG
>>
>>
>>Option #1
>>
>>         |                                   |
>>          |-----||--||--||--||--||--||--||--||----|
>>          |                                   |
>>--IN----|                                   |---------- OUT --->
>>          |                                   |
>>          |-----||--||--||--||--||--||--||--||----|
>>          |                                   |
>>          |                                   |
>>          ^                                  ^
>>          Aluminium Strip            Aluminium Strip
>>
>>
>>
>>
>>Option #2
>>
>>     |
>>     |-----||--||--||--||--||--||--||--||-------------- OUT --->
>>     |
>>     |
>>     |
>>     |-----||--||--||--||--||--||--||--||---------------IN-----
>>     |
>>     |
>>     ^
>>     Aluminium Strip
>>
>>
>>
>>
>>
>>-Glen
>>
>>
>>
>>
>>
>>
>>