Re: 1st Tesla Coil WONT LIGHT HELP PLEASE!

["Tesla list" <tesla-at-pupman-dot-com>]

Original poster: "Aaron Aab" <striker754-at-earthlink-dot-net> 

pop bottles are plastic, at least around here


----- Original Message -----
From: "Tesla list" <tesla-at-pupman-dot-com>
To: <tesla-at-pupman-dot-com>
Sent: Friday, January 23, 2004 3:50 PM
Subject: Re: 1st Tesla Coil WONT LIGHT HELP PLEASE!


 > Original poster: "Jim Mitchell" <electrontube-at-sbcglobal-dot-net>
 >
 > Soda bottles?!? Aluminum?  If so that will not work you need glass
bottles.
 >
 > Regards - Jim Mitchell
 > ----- Original Message -----
 > From: "Tesla list" <tesla-at-pupman-dot-com>
 > To: <tesla-at-pupman-dot-com>
 > Sent: Friday, January 23, 2004 1:28 PM
 > Subject: Re: 1st Tesla Coil WONT LIGHT HELP PLEASE!
 >
 >
 >  > Original poster: "Aaron Aab" <striker754-at-earthlink-dot-net>
 >  >
 >  > I'm guessing you dont ahve enough capacitance or spark gap is too big
for
 >  > the power level.
 >  >
 >  > I'm not sure how much uF each of those bottles is worth, maybe 0.01?
 >  >
 >  > Try moving the spark gap closer together, the transformer you have is
 > fairly
 >  > small.
 >  >
 >  > Aaron
 >  >
 >  > ----- Original Message -----
 >  > From: "Tesla list" <tesla-at-pupman-dot-com>
 >  > To: <tesla-at-pupman-dot-com>
 >  > Sent: Friday, January 23, 2004 8:02 AM
 >  > Subject: Re: 1st Tesla Coil WONT LIGHT HELP PLEASE!
 >  >
 >  >
 >  >  > Original poster: "Nightmare" <nightmare-at-bak.rr-dot-com>
 >  >  >
 >  >  >
 >  >  >
 >  >  > Hi, this is ravi, i just made my first TC and it wont light, i wired
 >  >  > everything up right but it still wont light! It was grounded and
 >  >  > everything. I plug it in and nothing happens. I tested the
transformer
 > by
 >  >  > plugging it in and the terminals arc to each other like a jacobs
ladder
 >  > and
 >  >  > it works, but nothing happens when i plug it in! All i hear is the
 > humming
 >  >  > of the transformer Please help. I  ve experimented and done all i
can .
 > I
 >  >  > need this done by next Friday for science fair so please help. The
 > spark
 >  >  > gap doesnt fire either, ive tried 2 different transformers and the
same
 >  >  > thing. Please email me off group for picctures since it doesnt
support
 >  >  > attatchments. Here are my coil specs:
 >  >  > Secondary: 22inx3in 18in windings
 >  >  > Primary: ~7-8 turns of 1/4in copper tubing with various adjusted
taps
 > with
 >  >  > clip.
 >  >  > Caps: 4 soda bottles covered in foil wrapped in elec. tape. filled
with
 >  >  > salt water. all connected with ring terminals
 >  >  > Spark gap: 2 1.25in dia copper pipes 3.25in long
 >  >  > Transformer: 1st is 7.5kV 30mA 60Hz 2nd one i tried is 4.0-4.5kV
30mA
 >  > 50/60Hz
 >  >  > Toroid, 3in air cond duct with 2 pie plates like this >--< in center
to
 >  >  > hold in place 9 in inner dia 15 in outer dia.
 >  >  > Everything is conected with ring terminals and 600V hardware wire,
and
 >  >  > gator clips for primary.
 >  >  > I used the schematics on deepfriedneon-dot-com exept with diff. gap and
 > bottle
 >  >  > caps instead of MMC's. Please help me I've done all i can. Again, if
 > you
 >  >  > need pics please email me seperately and i will send them. Thank A
 > LOT!!!!
 >  >  >
 >  >  >
 >  >  > A desperate 8th Grader,
 >  >  >
 >  >  > Ravi
 >  >  >
 >  >  >
 >  >  >   Thanks A LOT for the help.            Thanks A LOT again
 >  >  >
 >  >  > Ravi
 >  >  >
 >  >  >
 >  >  >
 >  >
 >  >
 >
 >