RE: Tesla coil grounding and other questions

["Tesla list" <tesla-at-pupman-dot-com>]

Original poster: JOSEPH CACCIATORE <jocatch-at-us.ibm-dot-com> 


Great Luke. I went to that site and they had some of the best prices and 
since YOU said they were good, 8-), I ordered a 2000' spool of #28 wire. 
Ships tomorrow I hope.

Last problem I have is finding some caps. Geek is out until next month and 
there is nothing on Ebay. I need to find another place to get some 
polyester caps. Sounds like pants, uh? 8-)

JC



"Tesla list" <tesla-at-pupman-dot-com>

02/17/2004 07:04 PM
To
tesla-at-pupman-dot-com
cc
Subject
RE: Tesla coil grounding and other questions




Original poster: "Luke" <Bluu-at-cox-dot-net>

JC:
I looked around and found nothing in the way of wire locally as well.
Unless I ordered through JCH wire and cable (local place here)  they
wanted a tone of cash for it.

But I found the wire is pretty cheap at McMaster Carr (McMaster-dot-com).
Go to their web site and in the search window type in "magnet wire"
then on the right side frame scroll to the bottom.

I paid $16.36 for my 3000' spool of #26 wire.  Their online catalog
rocks!! IMO.

Oh yeah I called before I ordered it thinking the shipping would be
high.  Turns out it would be about 5 bucks.  And I ordered other stuff
with it.

Hope that helps

Luke Galyan
Bluu-at-cox-dot-net

-----Original Message-----
From: Tesla list [mailto:tesla-at-pupman-dot-com]
Sent: Tuesday, February 17, 2004 6:11 AM
To: tesla-at-pupman-dot-com
Subject: Re: Tesla coil grounding and other questions

Original poster: JOSEPH CACCIATORE <jocatch-at-us.ibm-dot-com>


John, checked out your design. Looks really good and easy to build. I
have
one question, however. And it is a generic question too. For a 12kv, 30
ma,
60 hz NST, the capacitor works out to be .0066uf. Yet you and alot of
other
designs use much bigger caps. How can you still tune? With the program I
am
using for design, changing the cap from .006 to something larger meshes
up
all the parameters making it impossible for me to still use a 4"
diameter
secondary with a 5:1 aspect and still tune it. Maybe I need to play with

the numbers some more...

I did go to Home Depot and Lowes and I must say I am very disappointed
with
their wire selection. I wanted to get some 10 gauge solid wire to
emulate
what you did and they had none. All I was able to get was 8 gauge bare,
solid wire. Not a problem really. But no one had any wire smaller than
18
gauge, no 22, 24, 26, 28, no nothing. So I need to look around the area
some more. I did pick up a long 12' PVC drainage pipe for about $5. That

wasn't bad. I also picked up 2 end caps for 94 cents for the pvc so I
can
make a rig to spill it when I do wind the wire on it.

JC




"Tesla list" <tesla-at-pupman-dot-com>

02/16/2004 01:54 PM
To
tesla-at-pupman-dot-com
cc
Subject
Re: Tesla coil grounding and other questions




Original poster: FutureT-at-aol-dot-com

In a message dated 2/15/04 8:29:06 PM Eastern Standard Time,
tesla-at-pupman-dot-com writes:

  >As you may have gathered from my other post I plan to start from
scratch
  >and build a 4 or 4.25" secondary coil using my 12kv NST. Looks like I
will
  >buy some MMC caps on ebay if I can find them or from the Geek site.


JC,

You may want to check out my TT-42 type coil at my website
which uses a 12/30 NST and a 4.25" dia secondary and gives
42" sparks.   There's a link there to John Morawa's TC which is
prettier than mine I must say, and it uses 1/4" tubing on the primary.

<http://hometown.aol-dot-com/futuret/page3.html>http://hometown.aol-dot-com/futu
ret/page3.html

John