[Prev][Next][Index][Thread]
RE: Series or parallel? (fwd)
---------- Forwarded message ----------
Date: Fri, 13 Feb 1998 07:47:38 -0500
From: "Thornton, Russ #CSR2000" <ThorntoR-at-rc.pafb.af.mil>
To: 'Tesla discussion Group' <tesla-at-pupman-dot-com>
Subject: RE: Series or parallel? (fwd)
Sorry if this is redundant but I am coming in late on this discussion.
Are you saying this:
----/\/\/\/\/\--------/\/\/\/\/\----------------------
0 50 0 50 0
0 0 0
0|0 0|0 0|0
0|0 0|0 0|0
0 0 0
0 0 0
----/\/\/\/\/\--------/\/\/\/\/\----------------------
50 50
If this is right could you explain what the reason is for this?
Russ Thornton
CSR 2040,
Building 989, Rm. A1-N20
Phone: (407) 494-6430
Email: thorntor-at-rc.pafb.af.mil
>----------
>From: Tesla List[SMTP:tesla-at-pupman-dot-com]
>Sent: Wednesday, February 11, 1998 10:11 PM
>To: 'Tesla List'
>Subject: Series or parallel? (fwd)
>
>
>----------
>From: D.C. Cox [SMTP:DR.RESONANCE-at-next-wave-dot-net]
>Sent: Wednesday, February 11, 1998 12:03 PM
>To: Tesla List
>Subject: Re: Series or parallel? (fwd)
>
>to: Brian
>
>When running multiple NST's use a 20-50 Ohm, 50 Watt resistor on each NST.
>The paralled outputs are then routed through the usual protective
>resistive-inductive circuitry.
>
>DR.RESONANCE-at-next-wave-dot-net
>
>
>> From: Basura, Brian D [SMTP:Brian.Basura-at-unistudios-dot-com]
>> Sent: Tuesday, February 10, 1998 12:18 PM
>> To: 'Tesla List'
>> Subject: RE: Series or parallel? (fwd)
>>
>> Hello,
>>
>> What if you are running multiple NST's in parallel. Should the NST's
>> secondary be connected together then to the resistors/inductors or
>> should each NST have it's own protection?
>>
>> Thanks,
>> Brian D. Basura
>> USITG - Manager, Technical Support
>> (818) 777-0979
>>
>>
>> > ----------
>> > From: Tesla List[SMTP:tesla-at-pupman-dot-com]
>> > Sent: Sunday, February 08, 1998 6:48 PM
>> > To: 'Tesla List'
>> > Subject: Series or parallel? (fwd)
>> >
>> >
>> > From: D.C. Cox [SMTP:DR.RESONANCE-at-next-wave-dot-net]
>> > Sent: Saturday, February 07, 1998 1:04 PM
>> > To: Tesla List
>> > Subject: Re: Series or parallel? (fwd)
>> >
>> > to: Tim
>> >
>> > Running the cap in parallel with the power source and the spark gap in
>> > series (like most schematics show) is the best possible way to insure
>> > the
>> > reasonably quick death of your NST. Always run the gap (stationary or
>> > rotary) in parallel with the NST and the cap in series with the
>> > adjustable
>> > primary tap. Be sure to use some protection between your NST and the
>> > gap
>> > (on each leg) to prevent any spikes kicking back. 500-1000 Ohms of
>> > resistance in series with a small air core inductor works fine.
>> >
>> > DR.RESONANCE-at-next-wave-dot-net
>> >
>> >
>> >
>> >
>> >
>> > ----------
>> > > From: Tesla List <tesla-at-pupman-dot-com>
>> > > To: 'Tesla List' <tesla-at-pupman.-dot-com>
>> > > Subject: Series or parallel? (fwd)
>> > > Date: Saturday, February 07, 1998 12:33 AM
>> > >
>> > >
>> > > Date: Thu, 5 Feb 1998 19:00:39 -0700
>> > > From: Tim Dempsey <tdempsey-at-easley-dot-net>
>> > > To: Tesla List <tesla-at-pupman-dot-com>
>> > > Subject: Series or parallel?
>> > >
>> > > Hello all,
>> > >
>> > > I've seen several references to running tesla coils is a series
>> > circuit
>> > > as follows:
>> > >
>> > > neon secondary--cap--tesla primary--neon secondary
>> > >
>> > > Would the spark gap be placed across the cap and the tesla primary
>> > and
>> > > what are the advantages of running a coil in this fashsion or am I
>> > > misunderstanding ? Most schematics I've seen show the cap in
>> > parallel
>> > > with the neon and the spark gap inbetween one leg of the cap and
>> > tesla
>> > > primary. Also, I would like to know where the strike rail for the
>> > > primary connects into the circuit? Thanks in advance.
>> > >
>> > >
>> > > New coiler
>> > >
>> > > Tim Dempsey
>> > >
>> > > tdempsey -at-easley-dot-net
>> > >
>> > >
>> >
>> >
>> >
>>
>
>
>