[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

Re: Terry`s DRSSTC, gate drive



Original poster: Steve Ward <steve.ward@xxxxxxxxx>

Hey Terry,

I didnt notice how you were powering your gate drivers, excellent
solution there ;-).  The only complaint i have is that now you cant
use a variac to power the coil... well, you at least need 30V or so on
the bridge.  But you were set on the idea of no variac, so it looks
like you got what you wanted ;-).  Im still using them, but thinking
about making PWM to supply my BIG coil at several kVA.

Anyway, Finn, the program I use is express PCB, you can get it at
www.expresspcb.com.  Im pretty sure thats what Terry is using too
since that is where he ordered his PCBs from.  Its a simple and free
program.

Seeya,

Steve


On Thu, 10 Mar 2005 08:16:54 -0700, Tesla list <tesla@xxxxxxxxxx> wrote: > Original poster: Finn Hammer <f-h@xxxx> > > Terry, > > No, I think I finally get it. > > You seem to be using the same schematic capture program as Stephen Ward > does. Which program is that? > > Cheers, Finn Hammer > > Tesla list wrote: > > >Original poster: Terry Fritz <teslalist@xxxxxxxxxxxxxxxxxxxxxxx> > > > >Hi Finn, > >

> >At 01:37 PM 3/9/2005, you wrote:
> >
> >>Terry,
> >>
> >>First of all, allow me to express my admiration of the way you went about
> >>designing and debugging your DRSSTC. I think it is quite remarkable to
> >>witness your openness, your skill and quite frankly your restraint to not
> >>just "turn up the wick", but wait untill the circuit checks out on the scope.
> >
> >
> >Thanks!!
> >
> >
> >>Bravo!
> >>
> >>You did once explain how the powering of the gate drivers was acheived,
> >>but I missed the point.
> >>Do you think you could post a schematic of the H-Bridge with one the
> >>drivers in place.
> >>I don`t understand how you derive the 0V reference to the middle of the
> >>bridge, for driving the upper 2 IGBT`s, from the rails,
> >
> >
> >Here is a diagram of 1/2 the bridge with the two drivers and the schematic
> >of one gate driver:
> >
> >http://hot-streamer.com/temp/OpticalGateDriveHook.gif
> >
> >http://drsstc.com/~terrell/schematics/OpticalGateDrive-1.0.gif
> >
> >The IGBTs are off most of the time so the output is basically
> >floating. But the two R1s on the gate drivers tend to force the output to
> >"around" zero volts. That allows the voltage across the drivers to be
> >about 170VDC so they can charge their power supply storage caps
> >(C2s). Once the C2 caps are charged up, it can drive the gates for about
> >1 second which is much more than enough storage time as the voltage across
> >the drivers oscillates wildly during the firing cycle.
> >
> >On the lower side, the collector is tied to the output and the emitter of
> >the upper driver is also tied to the output. When the output is going
> >between +170 and -170 during the firing, these circuits "ride" right along
> >with the output voltage!! Not a big deal for the lower one since R1 and
> >R2 provide a lot of isolation. But the upper one has the whole "virtual
> >ground" connected to the output so everything on the circuit oscillates
> >with the output voltage there!! But it seems to work perfectly fine
> >(heavy short wire hook ups!!).
> >
> >Let me know if this is still not clear.
> >
> >Cheers,
> >
> > Terry
> >
> >
> >
> >>Cheers, Finn Hammer
> >
> >
> >
>
>